General Type: Heavy-duty industrial/commercial Brand: Briggs Vanguard Big Block EFI

 

Model: 61G2 Horsepower: 40 HP @ 3600 RPM

 

Torque: data not published

 

Type: 4 cycle gas, twin-cylinder, air-cooled, fuel-injected, horizontal shaft engine

 

Displacement: 993 cc (60.6 cubic inch)

 

Cylinders: 2 cast-iron sleeves

 

Air Intake Group: 5", large capacity 2-stage canister air filter

 

Exhaust: Single canister muffler

 

Engine Idle Speed: Electronic governor with variable speed control set at 3800 rpm (±100 rpm), idle set at 1750 rpm (±100 rpm)

 

Fuel Group: Electronic fuel Injection system for maximum fuel efficiency. High pressure electric fuel pump with inline fuel filter. Choke free operation.

 

Oil Pump Group: Full pressure lube, capacity 2.3 Liter with spin-on oil filter

 

Starter/Electrical: 12 volt "maintenance-free" sealed battery (350 CCA) with alternator, Magnetron® Electronic Ignition, solenoid shift starter Charging System: 20 amp - regulated

Fuel Tank: Single, 12 gallon (45.4 liters) top-draw seamless tank with fuel gauge. Mounted low in the center of the mower to lower the center-of-gravity for increased hillside stability. Extra-large, angled filler neck for easy filling.

 

Drive Wheels/Tires: 26 x 12 - 12 six-ply pneumatic tubeless, radius edge, offset rims to improve operator’s view

 

Parking Brake: Foot-operated brake with park lock feature. AUSCO disc brakes feature a rotor and caliper style design for maximum holding power.

 

Frame: Compact frame design with welded, structural steel double tube construction. Engineered to provide a low center-of-gravity for increased stability on inclines.

Type: Hydro drive with two variable displacement pumps and two cast-iron motors for independent control of each drive wheel

 

Hydro Pumps: Two Hydro-Gear 16cc pumps with cooling fans and dump valves for movement without running engine. Internal shock valves to protect hydraulic system. Pump-mounted cooling fans for increased drive system protection.

 

Drive Wheel Motors: Two Parker 18 cubic inch cast-iron high-torque wheel motors

 

Transmission Belt Idler: Self-adjusting, self-tightening Hydro Fluid Cooling Group: 3 qt. system capacity with nylon fluid reservoir and external hydraulic oil coolers, uses SAE 20W50 fluid and 10 micron filter

 

Steering/Travel Control: Twin "Quick-Fit" lever fingertip steering control with gas shock dampeners for smooth, responsive control to each wheel

 

Axles: 1-1/4" heavy-duty, tapered motor shafts

 

Wire Harness: 14 and 16 gauge wire. Tightly wound protective wire loom. Dielectric grease at major electrical connections.

 

Safety Group: Seat actuated engine kill, neutral interlock, mower engagement (PTO) switch, parking brake

 

Instrument Panel: Key switch, throttle, fuses, manual choke, PTO switch, Tiger Eye Advanced Monitoring System, 12-volt accessory outlet.

 

Forward Ground Speed Range: 0 up to 12.0 mph

 

Reverse Ground Speed Range: 0 up to 5.0 mph

Type: Velocity Plus, floating, adjustable, anti-scalping, hybrid design combines out-front and bellymount designs, special raised front edge allows grasses to enter the deck standing upright for a fast, manicured cut.

 

Construction: Tri-Plate construction consists of a 10-gauge steel cutter deck top reinforced with 7-gauge upper support plate and an 11-gauge lower spindle support plate. These three layers of steel equal close to a 1/2" thick steel cutter deck top. Deck skirt is 7-gauge. Trim side wear pad protects deck and landscape.

 

True Cutting Width: 61.0 inches (155.0 cm)

 

Cutting Height Adjustment: Foot-operated pedal adjustment from operator’s seat, 1" to 6" in 1/4" increments; 3-position adjustable pedal accommodates various operator heights

 

Cutter Blades: Three (3) 21" high-strength blades Specifications subject to change without notice. Actual ground speeds may vary. Accessories subject to availability. 

 

Cutter Deck Drive: Double clamp drive shaft to 90 degree gear box

 

Cutter Deck Baffles: Velocity Plus deck baffles direct air flow for maximum quality-of-cut. Custom Cut Baffle allows adjustment to individual cutting conditions (7 positions).

 

Blade Engagement: Electric PTO via Ogura GT5 (350 ft. lb) clutch brake with control panel knob

 

Discharge Opening: Extra wide 18.5" tapered discharge opening. Spring-loaded, non-denting plastic discharge chute combines strength and flexibility. Minimizes damage to landscape and trees. Turbo-Baffle increases discharge velocity for an even spread of clippings.

 

Caster Wheels: 13 x 6.5 x 6 flat-free caster wheels with tapered roller bearing pivots Spindles: Heavy-duty 1-1/8" top dimension spindle shaft, cast-iron housing, tapered roller bearing, low maintenance with top access grease fitting and grease overfill relief poppet.

 

Spindle Pulleys: Split steel design with easily removed tapered hubs. Split steel is stronger than stamped or cast iron pulley designs.

 

Cutter Deck Belts: B-section with Kevlar cord

 

Anti-Scalp Rollers: Two front corner adjustable, three front center adjustable, two rear corner adjustable, two rear

R.O.P.S.: OSHA 1928 certified roll-over protection system. System has foldable design for loading into enclosed trailers. Retractable seatbelt included.

 

"Command Comfort" Operator Station: "Quick-Fit" adjustable control levers. 3-position adjustable deck lift pedal. Standard 4-point isomounted torsion spring suspension seat; adjusts to operator's weight for a stable, comfortable ride. Features forward/rearward adjustment with adjustable back angle.

 

Cup Holder: Built-in, within easy reach

 

Tiger Eye Advanced Monitoring System: Blue backlit monitoring screen is IP67 rated. Gauge monitors crucial system and safety functions; integrated hour meter and much more (functions vary by model)

 

Flat-Free Caster Tires: Semi-pneumatic caster tires eliminate downtime resulting from flats.

Length: 85.5" Tracking

 

Width: 56"

 

Width: 73.5" Width (with discharge in transport position): 62.75"

 

Height (with ROPS up) 68"

 

Height (with ROPS folded down) 46.5"

 

Weight: 1519 lbs