General Type: Heavy-duty industrial/commercial

Brand: Kawasaki

Model: FT730V-EFI

Horsepower: 26 HP @ 3600 RPM

Type: 4 cycle gas, electronic fuel injection (EFI), twin-cylinder, air-cooled, OHV, vertical shaft engine

Displacement: 726 cc (44.3 cubic inch)

Cylinders: 2 cast-iron cylinder liners

Governor: Electronic type governor with variable speed control set at 3600 rpm (±100 rpm), idle set at 1550 rpm (±150 rpm)

Air Intake Group: Large capacity centrifugal air intake system

Exhaust: Side-mount single canister

Fuel Pump Group: High pressure fuel injection technology with electronic fuel pump. Sequential multi-port fuel injection. Compact electronic control unit. Proven open loop design. Electronic altitude compensation.

Oil Pump Group: Full pressure lubrication with oil filter

Starter/Electrical: Electronic ignition with solenoid shift starter

Oil Filter: Top-mounted, quick change design for mess-free oil changes

Starter/Electrical: 12 volt "maintenance-free" sealed battery (350 CCA) with alternator, solid-state ignition with key start, Electronic spark system

Charging System: 30 amp

Fuel Tank: Dual tanks (9.5 gallons / 35.9 liters total) with extra-large easy-fill openings and over-sized fuel caps, remote mount switching valve, molded-in cup holder

Drive Wheels/Tires: 24 x 9.5 - 12 four-ply pneumatic tubeless, radius edge, wide offset rims for better traction

Parking Brake: Foot-operated brake with park lock feature. AUSCO disc brakes feature a rotor and caliper style design for maximum holding power.

Frame: Compact frame design with structural steel tube construction, welded. Engineered for a low center-of-gravity for increased incline performance.

Type: Hydro drive with two variable displacement pumps and two cast-iron wheel motors for independent control of each drive wheel

Hydro Pumps: Two Hydro-Gear Model 12cc pumps with cooling fans feature dump valves for movement without running engine. Built in pressure relief valves add to hydraulic system life and reliability by reducing high pressure fluid spikes.

Drive Wheel Motors: Two Parker 14.5 cubic inch cast-iron high-torque wheel motors

Transmission Belt Idler: Self-adjusting, self-tightening, with permanently lubricated bearings

Hydro Fluid Cooling Group: 4 qt. capacity nylon fluid reservoir, uses SAE 20W50 fluid and 10 micron filter

Steering/Travel Control: Twin lever fingertip steering control with gas shock dampeners for smooth, responsive control to each wheel

Axles: 1-1/4" heavy-duty, tapered motor shafts

Wire Harness: 14 and 16 gauge wire. Tightly wound protective wire loom. Dielectric grease at major electrical connections.

Safety Group: Seat actuated engine kill, neutral interlock, mower engagement (PTO) switch, parking brake

Instrument Panel: Mounted at the right side of the operating position for easy access. Key switch, throttle, fuses, PTO switch, Tiger Eye Advanced Monitoring System, and 12-volt accessory outlet.

Forward Ground Speed Range: 0 up to 12.0 mph

Reverse Ground Speed Range: 0 up to 5.0 mph

Type: Velocity Plus, floating, adjustable anti-scalping, hybrid design combines out-front and belly-mount designs, special raised front edge allows grass to enter the deck standing upright for a fast, manicured cut.

Construction: Tri-Plate construction consists of a 10-gauge steel cutter deck top reinforced with 10-gauge upper support plate and an 11-gauge lower spindle support plate. These three layers of steel equal close to a 1/2" thick steel cutter deck top. Deck skirt is 7-gauge. Trim side wear pad protects deck and landscape.

True Cutting Width: 52.0 inches (132.0 cm)

Cutting Height Adjustment: Foot-operated pedal adjustment with deck easy-access deck latch lever adjusts from operator’s seat, 1" to 5" in 1/4" increments.

Cutter Blades: Three (3) 18" high-strength cutter blades

Cutter Deck Baffles: Velocity Plus deck baffles direct air flow for maximum quality-of-cut. Custom Cut Baffle allows adjustment to individual cutting conditions (7 positions).

Blade Engagement: Electric PTO via Ogura GT3.5 (250 ft. lb) clutch brake with control panel knob

Discharge Baffles: Turbo-Baffle for extra discharge velocity with spring-loaded plastic discharge chute

Caster Wheels: 13 x 6.5 x 6 flat-free caster wheels(4-ply) with tapered roller bearing pivots and axles

Spindles: Heavy-duty 1-1/8" top dimension spindle shaft, cast housing, tapered roller bearing, low maintenance with top access grease fitting and grease overfill relief poppet

Idler Arms: Spring-loaded for continuous belt adjustment and longer life, permanently lubricated bearings

Spindle Pulleys: Split steel design with easily removed tapered hubs. Split steel is stronger than stamped or cast-iron pulley designs.

Cutter Deck Belts: B-section with Kevlar cord

Anti-Scalp Rollers: Two front 4-1/2" adjustable, two rear 10" fixed

R.O.P.S.: OSHA 1928 certified roll-over protection system. System has foldable design for loading into enclosed trailers.

Tiger Eye Advanced Monitoring System: Blue backlit monitoring screen is IP67 rated. Gauge monitors crucial system and safety functions; integrated hour meter and much more (functions vary by model)

Suspension Seat: 4-point iso-mounted suspension seat with padded arm rests, lever adjustment forward and back.

Cup Holder: Conveniently molded into left-side fuel tank.