General Type: Heavy-duty industrial/commercial

Brand: Kawasaki

Model: FX730V

Horsepower: 23HP minimum @ 3600 RPM

Type: 4 cycle gas, forced air-cooled, OHV, twin-cylinder, vertical shaft engine

Displacement: 726 cc

Cylinder: 2 cast-iron sleeves

Governor: Mechanical governor with variable speed control set at 3600 rpm (±100 rpm), idle set at 1550 rpm (±150 rpm)

Air Cleaner: Large capacity dual element canister air cleaner, chopper-type grass screen

Exhaust: Scag designed, low noise, low temperature, aluminized exhaust

Fuel Pump Group: Pulse-type fuel pump with in-line filter, fixed jet carburetor

Oil Pump Group: Positive displacement Gerotor Oil Pump

Starter/Electrical: 12 volt "maintenance-free" sealed battery (350 CCA) with alternator, solid-state ignition with key start, Electronic spark system

Charging System: 13 amp

Fuel Tank: Single 6.5 gallon tank with extra-large easy-fill opening, over-sized fuel cap, fuel gauge, moldedin cup holder and storage tray

Drive Wheels/Tires: 24 x 12 - 12 pneumatic tubeless, radius edge, wide offset rims for better traction

Parking Brake: Foot-operated brake with park lock feature. AUSCO disc brakes feature a rotor and caliper style design for maximum holding power.

Frame: Compact frame design with structural steel tube construction, welded. Engineered for an ultralow center-of-gravity for increased incline performance.

Foot Plate: Pierced, extruded steel tread pattern for permanent non-slip traction; rubber iso-mounted to reduce vibration and increase operator comfort.

Type: Hydro drive with two Hydro-Gear ZT-3400 hydro transaxles with charge pumps for independent control of each drive wheel

Transmission Belt Idler: Self-adjusting, self-tightening, with permanently lubricated bearings

Hydro Fluid: 5 qt. system capacity, uses SAE 20W50 fluid and 25 micron filters (one filter per transaxle)

Steering/Travel Control: Twin lever fingertip steering control with gas shock dampeners for smooth, responsive control to each wheel

Axles: 1.125" heavy-duty axle

Wire Harness: 16 gauge wire. Tightly wound protective wire loom. Dielectric grease at major electrical connections.

Safety Group: Seat actuated engine kill, neutral interlock, mower engagement (PTO) switch, parking brake Instrument

Panel: Mounted at the left side of the operating position for easy access. Key switch, throttle, fuses, manual choke, PTO switch. SmartSense digital hour meter displays maintenance reminders.

Forward Ground Speed Range: 0 up to 10.0 mph

Reverse Ground Speed Range: 0 up to 5.0 mph

Type: Floating Hero Cutter Deck, adjustable anti-scalping, hybrid design combines out-front and bellymount designs; cutting chamber design provides a fast, manicured cut.

Construction: Dual-plate construction consists of a 10-gauge steel cutter deck top reinforced with an 11-gauge spindle support plate. Deck skirt is 7-gauge.

True Cutting Width: 61.0 inches (154.94 cm)

Cutting Height Adjustment: Foot-operated pedal adjustment with deck easy-access deck latch lever adjusts from operator’s seat, 1-1/2" to 5" in 1/4" increments.

Cutter Blades: Three high-strength cutter blades

Blade Engagement: Electric PTO via Ogura GT2 (108 ft. lb) clutch brake with control panel knob

Caster Wheels: 13 x 6.5 - 6 caster wheels (4-ply) with maintenance-free igus® iglide® polymer sleeve bearings; dual sealed ball bearings in caster wheel pivots

Spindles: Heavy-duty spindle shaft, aluminum housing, sealed ball bearings, "maintenance-free" design

Idler Arm: Spring-loaded for continuous belt adjustment and longer life, maintenance-free iglide® polymer flange bearing

Spindle Pulleys: Split steel design. Split steel is stronger than stamped or cast-iron pulley designs.

Cutter Deck Belts: B-section with Kevlar cord

Anti-Scalp: One roller on left-front edge, two rollers on center-front edge, skid plate at rear-center

Deck Leveling: Four corner deck leveling system provides precise adjustment of pitch and level

Discharge Chute: Highly flexible discharge chute will not dent and is easy on landscaping features

R.O.P.S.: OSHA 1928 certified roll-over protection system. System has foldable design for loading into enclosed trailers. Retractable seatbelt included.

Seat: Ultra-comfortable adjustable suspension seat. Contoured for improved comfort and features armrests.

Cup Holder: Conveniently molded into right-side fuel tank.

Length: 79" Tracking

Width: 50.5"

Width: 73.5" Width (with discharge in transport position): 62"

Height (with ROPS): 61.5"

Turning Radius: zero radius turning Weight: 952 lbs.