General Type: Heavy-duty industrial/commercial

Brand: Kawasaki

Model: FX1000V-EFI

Horsepower: 38 HP @ 3600 RPM

Type: 4 cycle gas, twin-cylinder, air-cooled, vertical shaft engine

Displacement: 999 cc (61.0 cubic inch)

Cylinders: 2 cast-iron cylinder liners

Governor: Electric governor set at 3600 rpm (±100 rpm), idle set at 1550 rpm (±100 rpm)

Air Intake Group: Large capacity 2-stage canister air filter

Exhaust Group: Side-mount single canister

Fuel Group: Electronic fuel Injection system for maximum fuel efficiency. High pressure electric fuel pump with inline fuel filter. Choke free operation.

Oil Pump Group: Full pressure lubrication with oil filter

Starter/Electrical/Charging System: 12 volt "maintenance-free" sealed battery (350 CCA) with alternator, solid state ignition with key start. 20 amp charging system- regulated

Thickness: 7 gauge steel

Fuel Tank: 12 gallon total (45.4 liters), dual 6-gallon, seamless polyethylene

Drive Wheels/Tires: 24 x 12 - 12 four-ply pneumatic tubeless, radius edge

Brakes: Dynamic braking through hydro drive system; standard equipment parking brake

Operator Platform: Heavy gauge steel with extruded star pattern for no-slip footing. Elastomeric spring suspension for operator comfort.

Operator comfort pad: Large heavily-bolstered operator cushion can be easily removed without tools for access to hydraulics.

Type: Hydro drive with two variable displacement pumps and two cast-iron high-torque wheel motors for independent control of each drive wheel

Hydro Pumps: Two Hydro-Gear 16cc pumps with cooling fans and dump valves for movement without running engine

Drive Wheel Motors: Two Hydro-Gear 18 cu. inch high-torque, axial piston wheel motors

Hydro Fluid Cooling: Pump mounted cooling fans

Steering/Travel Control: Twin lever steering control with individual control to each wheel.

Dump Valves: Allows for movement without engine running

Axles: 1.25" heavy-duty, tapered motor shafts

Wire Harness: 14 and 16 gauge wire

Safety Group: Footplate-actuated operator presence system, blade/clutch and transmission interlock to engine kill

Tiger Eye Advanced Monitoring System: Blue backlit monitoring screen is IP67 rated. Gauge monitors crucial system and safety functions; integrated hour meter and much more (functions vary by model)

Forward Speed Range: 0 up to 11.6 mph

Reverse Speed Range: 0 up to 5.0 mph

Type: Out-front floating design with special raised front edge and baffling allows all types of grasses to stand up before the cutter blade makes contact for a clean finish without leaving uncut grass. Works extremely well in all grass types, tall or short, thick or fine. Velocity Plus cutter deck design allows grass to be cut faster and cleaner. Easy cutting height adjustments in the field with no tools.

Construction: 10-gauge steel cutter deck top with 7-gauge and 11-gauge support plates, 7-gauge deck skirt. Trim-side wear pad protects deck and landscape.

True Cutting Width: 61 inches (155 cm)

Cutting Height Adjustment: 2" to 6" in 1/4" increments

Deck Baffles: Adjustable Custom-Cut Baffle design. Allows the operator to adjust to their individual conditions and grass types for an unmatched quality-of-cut.

Turbo-Baffle: Cutter deck baffle that increases discharge velocity for an even spread of clippings.

Cutter Blades: Three (3) 21" high-strength steel cutter blades

Blade Engagement: Electric blade clutch engagement with dash panel switch

Discharge Opening: Extra wide 18.5" discharge opening with spring-loaded discharge chute

Caster Wheels: 13 x 6.5 - 6 flat-free semi-pneumatic, with tapered roller bearing pivots

Spindles: Heavy-duty 1-1/8" top dimension spindle shaft, cast-iron housing, tapered roller bearing, low maintenance with top access grease fitting and grease overfill relief poppet; grade 8 mounting hardware; 3-year warranty

Spindle Pulleys: Machined cast-iron pulley design with easily removed tapered hubs

Idler Pulley: Large 5" diameter pulley, welded and riveted construction, 1-3/8" O.D. bearings (double stacked ball bearings)

Idler Arm: Heavy-duty dual ball bearing mounting Cutter Deck Belts: B-section with Kevlar cord

Push Arms: Rear push arms allow for easy cutting height changing and increased durability

Length: 73.5"

Tracking Width: 53.2"

Width: 73.5"

Width (with discharge in transport position): 62.75"

Height: 47.75"

Turning Radius: zero radius turning

Weight: 1230 lbs.